iDMX.ai

Quick Start

iDMX PC Quick Start

A show can be ready in a few minutes. Connect the hardware, patch the lights, generate programs, adjust if you want, then build a music show.

  1. 01Connect
  2. 02Patch
  3. 03AI Programs
  4. 04Adjust
  5. 05Music Show

1Connect the hardware

The laptop connects by USB to a USB network card. A Cat5 cable runs from the card to the Art-Net box. DMX1 through DMX8 each go to a different stage light.

iDMX PC hardware: laptop, USB network card, Art-Net box, and DMX1 to DMX8
Laptop → USB → USB Network Card → Cat5 → ArtNet box → DMX1–DMX8
  1. Open Setting → Art-Net Setting and press Detect.
  2. The USB network card and the Art-Net box must share a subnet and use different addresses. The console default is 192.168.0.10, the box is 192.168.0.100, and both use 255.255.255.0.
  3. Press Apply to write the address onto the USB network card. Windows needs administrator rights to change the adapter.

Universe 1 leaves the console as Art-Net 0. The DMX ports on the right of the box receive Art-Net 1–8.

2Five areas

The top bar holds Desk, 3D Edit, Clear, AI Programs, Layout, Group, 3D View, Patch, and Save Show.

1 · LeftAttribute keys: Dimmer, Pan/Tilt, Colour, Gobo, Beam, Effects, Locate.
2 · CenterWindows: Layout, 3D View, Groups, Presets, Effects.
3 · RightEffects, AI Programs, Save to Cue, Music Shows, Undo.
4 · Bottom rightPlayback faders, the page number, and the Grand master.
5 · Bottom leftThree wheels, plus Clear, Light On, and Light Off.

3Patch the lights

Patch the fixtures into this show first. AI Programs does not build anything until fixtures are patched.

Patch window before any fixtures are patched
Press Patch on the top bar to open the patch window.
  1. Press Patch, then Patch New Fixture.
  2. Choose the fixture type, universe, and start address.
  3. If the type is not in the library, open Setting → Library and sync the library.
  4. Press Return when you are done.

4Place them on stage

After patching, place the lights on the plan and check them in 3D. AI Programs also opens these two windows.

Fixture Layout and 3D View
Fixture Layout is on the left. 3D View is on the right.

5Press AI Programs once

After the lights are patched, press AI Programs on the top bar or on the right. The software groups the fixtures and builds programs: Full On, colour, movement, plus Zoom, Focus, Gobo, Prism, Frost, and similar channels when the fixture has them.

  1. Press a program block to run it. Press it again to stop.
  2. Switch the list with By Effect, By Light, and By Group.
  3. Edit under a block changes only that program.
  4. Generate again adds only categories that are not already there.

6Adjust when you need to

You can skip this step. Use it to tweak a look, or to combine several AI programs into one of your own.

Wheels show Pan and Tilt after fixtures are selected
With fixtures selected, the wheels in area 5 show the current channel, such as Pan and Tilt.
  1. Select fixtures in Layout.
  2. Choose Dimmer, Colour, Pan/Tilt, and the other keys in area 1, then adjust them on the wheels in area 5. Light On turns the lights on. Light Off turns them off.
  3. You can also raise several playback faders so those programs output together.
  4. Press Save to Cue on the right. It stores the running programs and your channel edits onto one playback.

Programs you save appear under Mine in Playback. Clear removes temporary programmer values. It does not delete saved programs.

7Play from the faders

Area 4, at the bottom, is Playback. Raise a fader to output. Grand is the master level.

8Build a music show

Press Music Shows on the right. Load an mp3, then let AI record to the beat, or record the steps yourself.

Music Shows window with AI record, Style, and Time code
Music Shows: shows on the left, music and programs in the center, Time code on the right.
  1. Press + to create a show. If there is no show yet, the window also asks you to press +.
  2. Browse selects the mp3. Play beside it plays the music only, with no lights.
  3. To generate: choose Programs from and Style, then press AI record.
  4. To record by hand: press Record, play the music, and press the program blocks. Time code stores each step.
  5. The transport play button in the center runs the whole show, and the lights follow. Loop repeats it.
Programs fromWhich programs
Full on + MineFull On flashes on the beat, and Mine programs take turns
Mine + AIMine and AI programs together
MineOnly the programs you saved

Style is Soft, Party, Build, Chase, or Strobe. They differ in density and flash. The mp3 stays on this computer. Saving the show stores the music-show timeline. The audio file itself is not uploaded.

9Save

  1. Press Save Show, or press Ctrl+S.
  2. An unnamed show asks for a name. A * beside the name means there are unsaved changes.
  3. After you sign in, saving syncs the show to the account. The music file stays on this computer.

File also has New Show, Open Show, and Save Show As. Edit has Undo and Redo.

10Keys

KeyAction
F1Opens this guide. The menu is Help → Quick Start
Ctrl+SSave the show
Ctrl+Z / Ctrl+YUndo / Redo
LLocate the selected fixtures
EscClose the menu